Production of Gibberellic Acid by Solid-State Fermentation Using Wastes from Rice Processing and Brewing Industry.

Gibberellic acid (GA3) is a natural hormone present in some plants used in agricultural formulations as a growth regulator. Currently, its production on an industrial scale is performed by submerged fermentation using the fungus Gibberella fujikuroi, which is associated with low yields, leaving the purification stages with high costs. An alternative is solid-state fermentation (SSF), which makes it possible to obtain higher concentrations of product using low-cost substrates, such as agroindustrial by-products. This research investigated the use of raw rice bran (RRB) and barley malt residue (BMR) as substrates for GA3 production by the fungus Gibberella fujikuroi. Through two statistical designs, the effect of moisture (50 to 70 wt.%) and medium composition (RRB content between 30 and 70 wt.% to a mass ratio between RRB and BMR) was first evaluated. Using the best conditions previously obtained, the effect of adding glucose (carbon source, between 0 and 80 g·L-1) and ammonium nitrate-NH4NO3-(nitrogen source, between 0 and 5 g·L-1) on GA3 productivity was analyzed. The best yield was obtained using 30 wt.% RRB and 70 wt.% BMR for a medium with 70 wt.% of moisture after 7 days of process. It was also found that higher concentrations of NH4NO3 favor the GA3 formation for intermediate values of glucose content (40 g·L-1). Finally, a kinetic investigation showed an increasing behavior in the GA3 production (10.1 g·kg of substrate-1 was obtained), with a peak on the seventh day and subsequent tendency to stabilization.

Removal of dyes from water using Citrullus lanatus seed powder in continuous and discontinuous systems.

The objective of this study is to develop a low-cost biosorbent using residual seeds of the Citrullus lanatus fruit for the removal of cationic dyes. Physicochemical parameters such as pH, adsorbent mass, contact time, and temperature were evaluated for their effects on dye removal. The biosorbent is composed of lignin and cellulose, exhibiting a highly heterogeneous surface with randomly distributed cavities and bulges. The adsorption of both dyes was most effective at natural pH with a dosage of 0.8 g L-1. Equilibrium was reached within 120 min, regardless of concentration, indicating rapid kinetics. The Elovich model and pseudo-second-order kinetics were observed for crystal violet and basic fuchsin dye, respectively. The Langmuir model fitted well with the equilibrium data of both dyes. However, the increased temperature had a negative impact on dye adsorption. The biosorbent also demonstrated satisfactory performance (R = 43%) against a synthetic mixture of dyes and inorganic salts, with a small mass transfer zone. The adsorption capacities for crystal violet and basic fuchsin dye were 48.13 mg g-1 and 44.26 mg g-1, respectively. Thermodynamic studies confirmed an exothermic nature of adsorption. Overall, this low-cost biosorbent showed potential for the removal of dyes from aqueous solutions.

In this work, a novel biosorbent was developed using residual Citrullus lanatus fruit seeds that can efficiently remove cationic dyes from aqueous solutions. The biosorbent's composition includes lignin and cellulose, and its surface structure is highly heterogeneous, consisting of randomly distributed cavities and bulges. The biosorbent demonstrated a rapid and efficient adsorption capacity for both crystal violet and basic fuchsin, regardless of dye concentration. Moreover, the biosorbent was successfully employed in the treatment of a synthetic mixture containing several dyes and inorganic salts. Finally, the application of the biosorbent in continuous adsorption showed a low zone of mass transfer and high breakthrough time, indicating it to be an excellent material for fixed-bed operation. Overall, this study provides a low-cost and efficient alternative for the removal of dyes from aqueous solutions, with promising practical applications.

Preparation of alumina-supported Fe-Al-La composite for fluoride removal from an aqueous matrix.

Using groundwater for human consumption is an alternative for places with no nearby surface water resources. Fluoride is commonly found in groundwater, and the consumption of this water for a prolonged time in concentrations that exceed established limits by WHO and Brazilian legislation on water potability (1.5 mg L-1) can cause harmful problems to human health. For this reason, fluoride removal is an important step before water consumption. In this work, activated alumina was impregnated with Fe-Al-La composite and employed for the first time as an adsorbent for fluoride removal from an aqueous environment. XRD, SEM/EDS, FT-IR, and point of zero charge were used to characterize the prepared adsorbent. The adsorptive performance of adsorbent material was investigated by employing a 23-central composite design (CCD), and the obtained experimental conditions were pH = 6.5 and adsorbent dosage = 3.0 g L-1. A maximum adsorption capacity of 8.17 mg g-1 at 298 K and pH = 6.5 was achieved by Langmuir isotherm to describe the adsorption. The kinetic model that better described experimental data was Avrami, with the kav parameter increasing with the initial concentration from 0.076 to 0.231 (min-1)nav. The nature of adsorption was found to be homogeneous, and it occurs in a monolayer. The fluoride removal performance for the prepared adsorbent was higher than granular activated alumina, showing that supporting Fe-Al-La at the alumina surface increased its fluoride adsorption capacity from 16 to 42% at the same experimental conditions. Finally, the influence of co-existing ions Cl-, SO42-, and NO3- was evaluated in fluoride adsorption, and the material presented great selectivity to fluoride. Thus, Fe-Al-La/AA adsorbent is a promising material for fluoride removal from water.

Effective adsorptive removal of textile pollutant using coal bottom ash with high surface area obtained by alkaline fusion route.

In this work, coal bottom ash was modified by alkaline fusion route in order to improve its pore properties and make it a potential adsorbent to remove crystal violet dye from aqueous medium. The solids were characterized and posteriorly subjected to kinetic, isotherm, and thermodynamic studies, as well as regenerated and reused for five adsorption tests. The alkaline fusion step resulted in the amorphization of material and generation of high surface area (102 m 2 g -1) and pore volume (0.180 cm 3 g-1), resulting in superior performance compared to the raw material. Kinetic and equilibrium studies showed that the adsorption process was better adjusted by the pseudo-second order and Langmuir models, respectively. The maximum adsorption capacity at equilibrium was 177. 37 mg g-1, with the adsorptive step occurring spontaneously and endothermically. The adsorbent maintained notable levels of dye removal after five consecutive cycles of thermal regeneration and reuse. Besides, the adsorbent was able to remove 64% of the colour of simulated industrial wastewater. Therefore, the alkaline fusion step proved to be a route capable of transforming the coal bottom ash into an adsorbent with improved textural and adsorptive properties.

Stable Resin Bonding to Y-TZP Ceramic with Air Abrasion by Alumina Particles Containing 7% Silica.

PURPOSE: To evaluate the influence of new air-abrasion powders with different silica concentrations (silica-coated aluminum oxide) and aging on the bond strength between composite cement and Y-TZP ceramic. MATERIALS AND METHODS: Ceramic slices (7 x 6.3 x 2 mm3) were randomly allocated into 8 groups (n = 20) considering different surface treatments (SiC: silica-coated aluminum oxide particles; AlOx: aluminum oxide particles; 7% Si and 20% Si: experimental powders consisting of 7% and 20% silica-coated of AlOx respectively) and aging (baseline: 24 h at 37°C in water; aged: 90 days at 37°C in water + 12,000 thermal cycles). A blinded researcher performed the air-abrasion procedure for 10 s (identical parameters for all groups). Composite resin cylinders (Ø = 3 mm) were cemented onto the silanized ceramic surfaces, light cured, and subjected to shear bond-strength testing (wire loop Ø = 0.5 mm). The topography of the powders and air-abraded surfaces was analyzed using SEM and atomic force microscopy (AFM). The elemental composition of the powders and air-abraded surfaces was analyzed with energy dispersive spectroscopy (EDS), and surface wetting of the air-abraded surfaces was also determined by contact-angle measurements. RESULTS: Under baseline conditions, all groups presented similar bond strengths, but only SiC and 7% Si yielded unaltered bond strength after aging. SiC and 7% Si presented lower contact angles. All groups presented similar surface topographies. The silica content was also similar among groups, except for AlOx. CONCLUSION: 7% Si and SiC presented similar bond strength and better bonding performance after aging than AlOx and 20% Si. A higher silica concentration was not able to promote stable adhesion of composite cement after aging.

Solid wastes from the enzyme production as a potential biosorbent to treat colored effluents containing crystal violet dye.

Sugarcane bagasse, a largely available waste worldwide, was submitted to solid-state fermentation (SSF) using the fungus Metarhizium anisopliae, aiming to produce enzymes. The solid waste generated from SSF was tested as an alternative biosorbent to treat colored effluents containing crystal violet (CV) dye. The biosorbent, here named BW (bagasse waste), was characterized, and experimental tests were performed to verify the influence of pH and dosage on the CV biosorption. Isotherms and biosorption kinetics were performed, and the biosorption thermodynamic parameters were determined. The potential of BW was also evaluated for the treatment of a simulated textile effluent. The maximum biosorption capacity was 131.2 mg g-1 at 328 K, and the Liu was the most appropriate model to represent equilibrium data. The biosorption was spontaneous and endothermic. The use of BW in the simulated effluent showed that it is an efficient material, reaching color removal values of 85%. Therefore, the sugarcane bagasse generated from SSF can be considered a potential biosorbent to remove CV from textile effluents. This finding is relevant from the total environment viewpoint, since, at the same time, SSF generates enzymes and a solid waste, which in turn can be used as biosorbent to treat colored effluents.

Lipases in liquid formulation for biodiesel production: Current status and challenges.

Enzymatic synthesis of biodiesel showed advantageous characteristics in relation to other technologies once it works under bland conditions, no generation of wastewater, no occurrence of saponifications reactions and production of a biodiesel with high quality. Although many researches still apply immobilized lipases, the high costs associated with this biocatalyst hamper the economic viability of the process. Lipases in free/soluble/liquid formulation employed to biodiesel production via hydroesterification reaction have attracted interest from researchers because they are more cost effective than the immobilized form, making the enzymatic route more competitive. In addition, soluble lipases present higher reaction rates, reducing the time required to obtain a satisfactory biodiesel yield. Despite the fact that already exist industrial plants producing biodiesel with the assistance of lipases in liquid formulation, results of researches show that the process still needs to overcome some drawbacks. This paper is a comprehensive and critical discussion on the publications where soluble lipases were applied on biodiesel synthesis, as well as the challenges that the technology faces and its current status in pilot and industrial applications.

Improving the soluble lipase-catalyzed biodiesel production through a two-step hydroesterification reaction system.

The application of lipases in liquid formulation instead of immobilized forms in the enzymatic biodiesel synthesis can make the process cost-efficient, more competitive, and sustainable. However, despite the benefits, the long reaction times required to achieve satisfactory yields is still a drawback of this biotechnological process. In this sense, employing the novel low-cost soluble NS40116 lipase, this paper proposes an innovative two-step hydroesterification reaction (TSHR) system as a technique of improving the reaction rate of an enzymatic biodiesel production. With the employment of two central composite statistical design to optimize the parameters of each of the reactions involved, the influence of the parameters "water concentration added to the reaction," "methanol-to-oil molar ratio," and "lipase load" on the process yield, besides the acid value of the samples, was investigated. After only 8 h of reaction, the highest fatty acid methyl ester yield reached was 97.1% with an acid value of 4.62 mg KOH g-1 utilizing a total of 8 wt% water, methanol-to-oil molar ratio of 6.3:1, and 0.70 wt% of lipase. Furthermore, the statistical models for both reactions indicated to be significant with 95% of reliability. Considering that the papers published using soluble lipases in a one-step batch process normally reach similar yields to those obtained in this research after 16 h to 24 h of reaction, the proposed system demonstrated to be a promising option of process configuration for the enzymatic production of biodiesel.

Biosorption of crystal violet dye using inactive biomass of the fungus Diaporthe schini.

An inactive biomass of a new fungus recently discovered, Diaporthe schini, was evaluated for the biosorption of crystal violet (CV) in simulated textile effluents. The characterization assays were performed using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and N2 adsorption/desorption isotherms. The influences of pH and biosorbent dosage on the biosorption capacity were evaluated. Kinetics, equilibrium and thermodynamic studies were also carried out. Characterization techniques showed an amorphous biosorbent, with a rough surface containing irregular particles and surface area of 6.5 m2 g-1. The most adequate values of pH and biosorbent dosage were 7.5 and 0.4 g L-1, respectively. The Elovich kinetic model and the Sips equilibrium model were suitable to fit the experimental data. The biosorption capacity increased with temperature, reaching a maximum biosorption capacity of 642.3 mg g-1 at 328 K. The biosorption was a spontaneous and endothermic process. Diaporthe schini inactive biomass was an interesting biosorbent to treat colored effluents, presenting efficiency of 87% in the decolorization of a simulated dye house effluent.

Enzyme-Catalyzed Production of FAME by Hydroesterification of Soybean Oil Using the Novel Soluble Lipase NS 40116.

The performance of lipase NS 40116, a novel and promising soluble enzyme obtained from modified Thermomyces lanuginosus microorganism, was investigated in the production of biodiesel (fatty acid methyl esters-FAME) by hydroesterification. In order to investigate the potential of the biocatalyst in its soluble form, this work reports the effect of water content and enzyme load, as well as the recovery and reuse of the biocatalyst. A FAME yield of 94.30% after 12 h was achieved at 35 °C by combining 0.50 wt% of lipase, 15 wt% of water, and a methanol:oil molar ratio of 4.5:1. The analysis of the time course reaction suggests that the triacylglycerides (TAGs) are hydrolyzed by the enzyme in a first step, generating free fatty acids (FFAs), followed by the esterification of these FFAs into FAME. In relation to the reusability assays, the lipase kept approximately 90% of its catalytic activity after five cycles of reuse. In this context, the findings of this study demonstrate that lipase NS 40116 can efficiently catalyze hydroesterification reactions under mild conditions, arising as a competitive alternative for biodiesel synthesis.

Soluble lipase-catalyzed synthesis of methyl esters using a blend of edible and nonedible raw materials.

This work investigates the use of blends of edible and nonedible raw materials as an alternative feedstock to fatty acid methyl esters (FAME) production through enzymatic catalysis. As biocatalyst, liquid lipase from Thermomyces lanuginosus (Callera™ Trans L), was used. Under reaction conditions of 35 °C, methanol to feedstock molar ratio of 4.5:1 and 1.45% of catalyst load, the best process performance was reached using 9% of water concentration in the medium-yield of 79.9% after 480 min of reaction. In terms of use of tallow mixed with soybean oil, the best yield was obtained when 100% of tallow was used in the process-84.6% after 480 min of reaction-behavior that was associated with the degree of unsaturation of the feedstock, something by that time, not addressed in papers of the area. The results show that tallow can be used as an alternative to FAME production, catalyzed by soluble lipase.

Carbon nanotubes as supports for inulinase immobilization.

The commercial inulinase obtained from Aspergillus niger was non-covalently immobilized on multiwalled carbon nanotubes (MWNT-COOH). The immobilization conditions for the carbon nanotubes were defined by the central composite rotational design (CCRD). The effects of enzyme concentration (0.8%-1.7% v/v) and adsorbent:adsorbate ratio (1:460-1:175) on the enzyme immobilization were studied. The adsorbent:adsorbate ratio variable has positive effect and the enzyme concentration has a negative effect on the inulinase immobilization (U/g) response at the 90% significance level. These results show that the lower the enzyme concentration and the higher the adsorbent:adsorbate ratio, better is the immobilization. According to the results, it is possible to observe that the carbon nanotubes present an effective inulinase adsorption. Fast adsorption in about six minutes and a loading capacity of 51,047 U/g support using a 1.3% (v/v) inulinase concentration and a 1:460 adsorbent:adsorbate ratio was observed. The effects of temperature on the immobilized enzyme activity were evaluated, showing better activity at 50 °C. The immobilized enzyme maintained 100% of its activity during five weeks at room temperature. The immobilization strategy with MWNT-COOH was defined by the experimental design, showing that inulinase immobilization is a promising biotechnological application of carbon nanotubes.

CuO/ZnO coupled oxide films obtained by the electrodeposition technique and their photocatalytic activity in phenol degradation under solar irradiation.

CuO/ZnO coupled oxide films were electrodeposited onto an aluminum substrate and tested as photocatalysts in degradation of phenol molecules in aqueous solution under sunlight. The obtained films were characterized by X-ray diffraction, scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). The results showed that the photocatalytic activity of films was significant, especially to coupled oxide film with a CuO/ZnO ratio equal to 0.697, which presented about 70% degradation of the aromatic molecules and 42% of total organic carbon (TOC) removal at 300 min under solar irradiation. Therefore, this work highlights the potential application of CuO/ZnO coupled oxide films obtained by electrodeposition onto aluminum substrate in the field of photocatalysis.

Evaluation of activity of a commercial amylase under ultrasound-assisted irradiation.

The main objective of this work was to evaluate the effects of ultrasound irradiation on the activity of a commercial amylase. A central composite design was carried out to assess the effects of temperature and pH on the enzyme activity in the presence and absence of ultrasound irradiation. The activation energy, the influence of treatment time as well as the substrate concentration on enzyme activity were also determined in the presence and absence of ultrasound irradiation. The results demonstrated that the effect of temperature was less pronounced in the presence of ultrasound, resulting in a decreasing of about 80% in the activation energy in comparison with the value obtained in the absence. The enzyme showed activities about 3 times higher for temperatures up to 40 °C in the presence of ultrasound. The pH negatively affected the activity in the presence of ultrasound, whereas in the absence a positive effect was verified. The ultrasound irradiation is a promising technology to be used in enzymatic reaction due to its positive effects on enzyme activity.